Book Your Appointment

 

The author is making a few great pointers regarding A Step-by-Step Guide to Installing a Bathtub as a whole in the article down below.

Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is readily easily accessible, the task can relocate rapidly; if you have to open a wall to remove the old bathtub and also position the new tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have qualified yourself for the task and fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to consider employing one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new bath tub in your bathroom if you have currently purchased a new bathtub and don't require to alter the setup of your previous supply of water pipes.
Your tools and also product list ought to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.

 

 

Setting up the Bathtub

Using both wooden boards under its feet, put the tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bathtub up until the spirit level checks out level.
To install taps, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Load the bath tub and additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling and also sealing around the tub ought to wait until the bath tub has actually been made use of at the very least once as this will certainly settle it into its final setting.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washing machines are in area in between the tap and the sink. Secure the tap in position with the supplier offered backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type ought to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Tub

In the area where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a stiff seal, causing the water to pass through the wall between the bath as well as the tiling, causing problems with wetness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are offered in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to permit the motion experienced when the bathtub remains in usage. The sealer can break fairly early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water resistant glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I stumbled upon that blog post on Installing A Bathtub while perusing the internet. For those who enjoyed reading our blog post if you please don't forget to pass it around. Thanks a lot for going through it.

Schedule